Schneider Electric EER50000

   
Model EER50000
Vendor Schneider Electric
Description Wiser H-Relay (HACT)
Exposes climate (occupied_heating_setpoint, local_temperature), power, energy, identify, zone_mode, hact_config, fip_setting, linkquality
Picture Schneider Electric EER50000

Notes

Pairing

This device by default only pairs to Wiser Gateways when the set button is pressed, to let it join normal HA gateways (like what Zigbee2MQTT uses) hold the set button down for 5 seconds, and release.

Options

How to use device type specific configuration

  • thermostat_unit: Controls the temperature unit of the thermostat (default celsius). The value must be one of celsius, fahrenheit

  • power_precision: Number of digits after decimal point for power, takes into effect on next report of device. The value must be a number with a minimum value of 0 and with a with a maximum value of 3

  • power_calibration: Calibrates the power value (percentual offset), takes into effect on next report of device. The value must be a number.

  • energy_precision: Number of digits after decimal point for energy, takes into effect on next report of device. The value must be a number with a minimum value of 0 and with a with a maximum value of 3

  • energy_calibration: Calibrates the energy value (percentual offset), takes into effect on next report of device. The value must be a number.

Exposes

Climate

This climate device supports the following features: occupied_heating_setpoint, local_temperature.

  • occupied_heating_setpoint: Temperature setpoint. To control publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"occupied_heating_setpoint": VALUE} where VALUE is the °C between 7 and 30. To read send a message to zigbee2mqtt/FRIENDLY_NAME/get with payload {"occupied_heating_setpoint": ""}.
  • local_temperature: Current temperature measured on the device (in °C). To read send a message to zigbee2mqtt/FRIENDLY_NAME/get with payload {"local_temperature": ""}.

Power (numeric)

Instantaneous measured power. Value can be found in the published state on the power property. It’s not possible to read (/get) or write (/set) this value. The unit of this value is W.

Energy (numeric)

Sum of consumed energy. Value can be found in the published state on the energy property. It’s not possible to read (/get) or write (/set) this value. The unit of this value is kWh.

Identify (enum)

Flash green tag for x seconds. Value will not be published in the state. It’s not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"identify": NEW_VALUE}. The possible values are: 0, 30, 60, 600, 900.

Zone_mode (enum)

Value can be found in the published state on the zone_mode property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"zone_mode": ""}. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"zone_mode": NEW_VALUE}. The possible values are: manual, schedule, energy_saver, holiday.

Hact_config (enum)

Input (command) and output (control) behavior of actuator. Value can be found in the published state on the hact_config property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"hact_config": ""}. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"hact_config": NEW_VALUE}. The possible values are: unconfigured, setpoint_switch, setpoint_fip, fip_fip.

Fip_setting (enum)

Output signal when operating in fil pilote mode (fip_fip). Value can be found in the published state on the fip_setting property. To read (/get) the value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/get with payload {"fip_setting": ""}. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"fip_setting": NEW_VALUE}. The possible values are: comfort, comfort_-1, comfort_-2, energy_saving, frost_protection, off.

Linkquality (numeric)

Link quality (signal strength). Value can be found in the published state on the linkquality property. It’s not possible to read (/get) or write (/set) this value. The minimal value is 0 and the maximum value is 255. The unit of this value is lqi.